K75 Mechanical Specifications

Models   KX | KM - Legacy Product
Screw Lead in 0.1969 0.3937 | 0.1969 0.3937
  mm 5 10 | 5 10
Maximum Force^2 lbf 2500 1250 | 2500 1250
  kN 11.1 5.6 | 11.1 5.6
Life at Maximum Force in x 10^6 2.4 22.6 | 0.6 5.6
  km 60.7 573.3 | 15.2 143.5
C_a (Dynamic Load Rating) lbf 5746 4820 | 3620 3036
  kN 25.6 21.4 | 16.1 13.5
Maximum Input Torque^1 lbf-in 98 98 | 98 98
  Nm 11 11 | 11 11
Max Rated RPM @ Input Shaft RPM 4000 4000 | 4000 4000
Maximum Linear Speed @ 
Maximum Rated RPM
in/sec 13.1 26.2 | 13.1 26.2
  mm/sec 333 666 | 333 666

1 - Input torque should be limited such that Max Force is not exceeded. For a parallel belt ratio, the input torque ratings must be divided by the belt ratio for allowable motor torque. The output force ratings remain the same.
2 - Maximum allowable actuator–generated force that can be applied routinely. Exceeding this force may result in permanent damage to the actuator. For maximum allowable externally-applied axial forces, consult factory. For high force, short stroke applications, consult factory.

 

K75 Inertias

  kg-m^-2 (lbf-in-sec^-2) kg-m^-2 (lbf-in-sec^-2)
  5 mm Lead Add per 25 mm, 5 mm Lead
Base Unit - Input Drive Shaft Only 9.26 x 10^-5 (8.20 x 10^-4) 3.13 x 10^-6 (2.77 x 10^-5)
Inline Unit - w/Motor Coupling 1.25 x 10^-4 (1.11 x 10^-3) 3.13 x 10^-6 (2.77 x 10^-5)
  10 mm Lead Add per 25 mm, 10 mm Lead
Base Unit - Input Drive Shaft Only 9.48 x 10^-5 (8.39 x 10^-4) 3.32 x 10^-6 (2.94 x 10^-5)
Inline Unit - w/Motor Coupling 1.44 x 10^-4 (1.28 x 10^-3) 3.32 x 10^-6 (2.94 x 10^-5)
Parallel Drive Inertias (P10 Option)
  5 mm Lead Add per 25 mm, 5 mm Lead
1:1 Reduction Parallel Belt Drive (86 mm) 2.29 x 10^-4 (2.03 x 10^-3) 3.13 x 10^-6 (2.77 x 10^-5)
1:1 Reduction Parallel Belt Drive (96 mm) 3.19 x 10^-4 (2.82 x 10^-3) 3.13 x 10^-6 (2.77 x 10^-5)
1:1 Reduction Parallel Belt Drive (130 mm) 5.96 x 10^-4 (5.28 x 10^-3) 3.13 x 10^-6 (2.77 x 10^-5)
2:1 Reduction Parallel Belt Drive (130 mm) 2.82 x 10^-4 (2.50 x 10^-3) 7.83 x 10^-7 (6.93 x 10^-6)
  10 mm Lead Add per 25 mm, 10 mm Lead
1:1 Reduction Parallel Belt Drive (86 mm) 2.31 x 10^-4 (2.05 x 10^-3) 3.32 x 10^-6 (2.94 x 10^-5)
1:1 Reduction Parallel Belt Drive (96 mm) 3.21 x 10^-4 (2.84 x 10^-3) 3.32 x 10^-6 (2.94 x 10^-5)
1:1 Reduction Parallel Belt Drive (130 mm) 5.98 x 10^-4 (5.30 x 10^-3) 3.32 x 10^-6 (2.94 x 10^-5)
2:1 Reduction Parallel Belt Drive (130 mm) 2.83 x 10^-4 (2.51 x 10^-3) 8.30 x 10^-7 (7.36 x 10^-6)
Parallel Drive Inertias (Smooth Motor Shaft Option)
  5 mm Lead Add per 25 mm, 5 mm Lead
1:1 Reduction Parallel Belt Drive (86 mm) 2.84 x 10^-4 (2.51 x 10^-3) 3.13 x 10^-6 (2.77 x 10^-5)
1:1 Reduction Parallel Belt Drive (96 mm) 4.25 x 10^-4 (3.76 x 10^-3) 3.13 x 10^-6 (2.77 x 10^-5)
1:1 Reduction Parallel Belt Drive (130 mm) 7.33 x 10^-4 (6.48 x 10^-3) 3.13 x 10^-6 (2.77 x 10^-5)
2:1 Reduction Parallel Belt Drive (130 mm) 3.32 x 10^-4 (2.94 x 10^-3) 7.83 x 10^-7 (6.93 x 10^-6)
  10 mm Lead Add per 25 mm, 10 mm Lead
1:1 Reduction Parallel Belt Drive (86 mm) 2.86 x 10^-4 (2.53 x 10^-3) 3.32 x 10^-6 (2.94 x 10^-5)
1:1 Reduction Parallel Belt Drive (96 mm) 4.27 x 10^-4 (3.78 x 10^-3) 3.32 x 10^-6 (2.94 x 10^-5)
1:1 Reduction Parallel Belt Drive (130 mm) 7.35 x 10^-4 (6.50 x 10^-3) 3.32 x 10^-6 (2.94 x 10^-5)
2:1 Reduction Parallel Belt Drive (130 mm) 3.33 x 10^-4 (2.94 x 10^-3) 8.30 x 10^-7 (7.35 x 10^-6)

 

K75 Weights

  lb kg
Base Actuator Weight (Zero Stroke) 6.75 3.06
Actuator Weight Adder (Per mm of Stroke) 0.0235 0.0107
Adder for Inline (excluding motor) 2.46 1.12
Adder for Parallel Drive (excluding motor) 4.06 1.84
Adder for Front Flange 1.91 0.87
Adder for Rear Flange 2.49 1.13
Adder for Rear Clevis 1.85 0.84
Adder for Rear Eye 1.85 0.84
Adder for Front/Rear Angle Mounts 1.37 0.62
Adder for Two Trunnions 1.56 0.71
Adder for Two Foot Mounts 2.47 1.12